Industrial process equipment in a treatment plant
Water Treatment Traitement de l'eau

Polymer Preparation Units: Dry vs Emulsion — Choosing the Right System

Unités de préparation de polymère : sec vs émulsion — choisir le bon système

Published · 3 min read

Publié le · 3 min de lecture

Polymers — or polyelectrolytes — are used in very small quantities, but they have a disproportionate influence on clarification and sludge dewatering performance. A poorly prepared polymer solution wastes product and degrades results. The preparation unit deserves as much attention as the polymer itself.

Why Polymer Preparation Matters

Organic polymers are used in water and wastewater treatment to flocculate suspended solids and to condition sludge before thickening or dewatering. They are delivered either as a dry powder or as a liquid emulsion, and in both cases must be diluted and allowed to mature (or "age") before they reach their full effectiveness.

Under-matured or poorly dispersed polymer forms lumps ("fish-eyes"), loses activity and leads to higher consumption. Over-diluted or inconsistently prepared solutions make the dewatering equipment harder to optimise. Automated preparation units exist to make this step consistent and repeatable.

Dry Polymer Systems

Powder polymers are concentrated products, which keeps transport and storage volumes low. The trade-off is that the powder must be wetted carefully: each particle needs to be dispersed in water before it starts to swell, and the solution then needs time to mature.

The Polymatic P unit manufactured by Sodimate is designed for powder polymers. It combines an accurate dry feed system with automated dilution, mixing and ageing. Based on the manufacturer's information, tanks are made of polypropylene (PPH) in sizes from 500 to 12,000 litres, with two or three mixing and ageing compartments. A complete pump skid is available as an option. Sodimate also offers loading accessories for powder polymers, such as a vertical vacuum loader and a vertical loader for filling the hopper.

Emulsion Polymer Systems

Emulsion polymers are supplied as liquids in which the active polymer is dispersed in an oil phase. They are pumped rather than conveyed, which simplifies handling and avoids dust. On the other hand, they contain a significant proportion of carrier and are generally bulkier to ship and store for the same quantity of active polymer.

The Polymatic E unit from Sodimate is dedicated to emulsion polymers. It is a compact, stacked unit with an enclosed pumping system and automated dilution and ageing. PPH tanks are available from 500 to 3,500 litres.

Head-to-Head Comparison

CriteriaDry PolymerEmulsion Polymer
Product formPowder, concentratedLiquid, polymer dispersed in an oil phase
HandlingBags or big bags; hopper loading; dust to be managedDrums or IBCs; pumped; no dust
Storage & transportCompact for a given quantity of active polymer; must be kept dryBulkier for the same active content; sensitive to extreme temperatures
PreparationAccurate wetting essential; longer maturationSimpler dilution; generally faster activation
Sodimate unitPolymatic P — PPH tanks 500 to 12,000 L, 2–3 compartmentsPolymatic E — compact stacked unit, PPH tanks 500 to 3,500 L
Typical fitMedium to large consumption, continuous operationSmaller consumption, compact sites, intermittent use

These are general tendencies rather than absolute rules; the right choice always depends on the polymer selected through jar tests, the consumption profile and the site constraints.

Selection Criteria for MENA Projects

  • Consumption. On large wastewater plants with continuous dewatering, the logistics savings of powder polymer often justify a dry preparation unit.
  • Climate. High temperatures affect both forms: powders must be protected from humidity, and emulsions from heat. Shaded or conditioned storage should be planned in either case.
  • Supply chain. Check which polymer grades and delivery formats are reliably available locally before freezing the design.
  • Footprint. Compact units such as the Polymatic E are well suited to containerised or space-constrained installations.
  • Operation and maintenance. Automated dilution and ageing reduce dependence on operator skill — an important factor on remote or lightly staffed sites.

Soditech, as Sodimate's representative in the region, can help contractors and operators specify the polymer preparation configuration best suited to their process.

Source: Sodimate, polymer preparation units (sodimate.com). Tank sizes as published by the manufacturer.

More about Sodimate →   Discuss your project →

Résumé en français — l'article complet est disponible en anglais (bouton EN).

Utilisés en très faibles quantités, les polymères ont pourtant une influence déterminante sur la clarification et la déshydratation des boues. Une solution mal préparée gaspille du produit et dégrade les résultats.

Polymère en poudre

Concentrée et économique à transporter, la poudre exige un mouillage précis et un temps de maturation. L'unité Polymatique P de Sodimate associe un dosage précis de la poudre à la dilution, au mélange et à la maturation automatisés, avec des cuves en polypropylène (PPH) de 500 à 12 000 litres et 2 à 3 compartiments.

Polymère en émulsion

Liquide, pompable et sans poussière, l'émulsion est plus volumineuse à quantité de matière active égale. L'unité Polymatique E est un ensemble compact superposé, avec pompage capoté et dilution automatisée, cuves PPH de 500 à 3 500 litres.

Bien choisir dans la région MENA

Consommation, chaleur et humidité, disponibilité locale des grades, encombrement et niveau d'automatisation sont les critères clés. Soditech, représentant de Sodimate, accompagne les EPC et exploitants dans ce choix. Le tableau comparatif complet est disponible dans la version anglaise.

En savoir plus sur Sodimate →   Parler de votre projet →